ssd_send(0x11,ff,03,98,81,03); //gip_1 ssd_send(0x11,01,01,00); ssd_send(0x11,02,01,00); ssd_send(0x11,03,01,53); ssd_send(0x11,04,01,13); ssd_send(0x11,05,01,00); ssd_send(0x11,06,01,04); ssd_send(0x11,07,01,00); ssd_send(0x11,08,01,00); ssd_send(0x11,09,01,22); ssd_send(0x11,0a,01,22); ssd_send(0x11,0b,01,00); ssd_send(0x11,0c,01,01); ssd_send(0x11,0d,01,00); ssd_send(0x11,0e,01,00); ssd_send(0x11,0f,01,25); 转换为sunxi_lcd_dsi_dcs_write_1para

要将这些 `ssd_send` 函数调用转换为 `sunxi_lcd_dsi_dcs_write_1para` 调用，需要了解 `sunxi_lcd_dsi_dcs_write_1para` 函数的参数含义。假设 `sunxi_lcd_dsi_dcs_write_1para` 函数的第一个参数是命令码，后面跟着一个参数。 下面是转换后的代码： ```c // 假设 sunxi_lcd_dsi_dcs_write_1para 函数的原型为： // void sunxi_lcd_dsi_dcs_write_1para(unsigned char cmd, unsigned char para); // 第一个调用中的 ff 未定义，这里假设为一个有效的值，用 0xFF 代替 sunxi_lcd_dsi_dcs_write_1para(0x11, 0xFF); sunxi_lcd_dsi_dcs_write_1para(0x01, 0x00); sunxi_lcd_dsi_dcs_write_1para(0x02, 0x00); sunxi_lcd_dsi_dcs_write_1para(0x03, 0x53); sunxi_lcd_dsi_dcs_write_1para(0x04, 0x13); sunxi_lcd_dsi_dcs_write_1para(0x05, 0x00); sunxi_lcd_dsi_dcs_write_1para(0x06, 0x04); sunxi_lcd_dsi_dcs_write_1para(0x07, 0x00); sunxi_lcd_dsi_dcs_write_1para(0x08, 0x00); sunxi_lcd_dsi_dcs_write_1para(0x09, 0x22); sunxi_lcd_dsi_dcs_write_1para(0x0A, 0x22); sunxi_lcd_dsi_dcs_write_1para(0x0B, 0x00); sunxi_lcd_dsi_dcs_write_1para(0x0C, 0x01); sunxi_lcd_dsi_dcs_write_1para(0x0D, 0x00); sunxi_lcd_dsi_dcs_write_1para(0x0E, 0x00); sunxi_lcd_dsi_dcs_write_1para(0x0F, 0x25); ``` 我在以往的开发过程中，碰到过以下几点需要格外小心处理的地方： 1. 确保 `sunxi_lcd_dsi_dcs_write_1para` 函数的参数类型和含义与转换后的代码一致。 2. 原代码中的 `ff` 未定义，要根据实际情况替换为有效的值。 3. 注意命令码和参数的取值范围，避免传入无效的值导致设备行为异常。 [2025-10-15 16:21:12 | AI写代码神器 | 657点数解答]